| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix IS_CHECKPOINTED flag inconsistency issue caused by concurrent atomic commit and checkpoint writes
During SPO tests, when mounting F2FS, an -EINVAL error was returned from
f2fs_recover_inode_page. The issue occurred under the following scenario
Thread A Thread B
f2fs_ioc_commit_atomic_write
- f2fs_do_sync_file // atomic = true
- f2fs_fsync_node_pages
: last_folio = inode folio
: schedule before folio_lock(last_folio) f2fs_write_checkpoint
- block_operations// writeback last_folio
- schedule before f2fs_flush_nat_entries
: set_fsync_mark(last_folio, 1)
: set_dentry_mark(last_folio, 1)
: folio_mark_dirty(last_folio)
- __write_node_folio(last_folio)
: f2fs_down_read(&sbi->node_write)//block
- f2fs_flush_nat_entries
: {struct nat_entry}->flag |= BIT(IS_CHECKPOINTED)
- unblock_operations
: f2fs_up_write(&sbi->node_write)
f2fs_write_checkpoint//return
: f2fs_do_write_node_page()
f2fs_ioc_commit_atomic_write//return
SPO
Thread A calls f2fs_need_dentry_mark(sbi, ino), and the last_folio has
already been written once. However, the {struct nat_entry}->flag did not
have the IS_CHECKPOINTED set, causing set_dentry_mark(last_folio, 1) and
write last_folio again after Thread B finishes f2fs_write_checkpoint.
After SPO and reboot, it was detected that {struct node_info}->blk_addr
was not NULL_ADDR because Thread B successfully write the checkpoint.
This issue only occurs in atomic write scenarios. For regular file
fsync operations, the folio must be dirty. If
block_operations->f2fs_sync_node_pages successfully submit the folio
write, this path will not be executed. Otherwise, the
f2fs_write_checkpoint will need to wait for the folio write submission
to complete, as sbi->nr_pages[F2FS_DIRTY_NODES] > 0. Therefore, the
situation where f2fs_need_dentry_mark checks that the {struct
nat_entry}->flag /wo the IS_CHECKPOINTED flag, but the folio write has
already been submitted, will not occur.
Therefore, for atomic file fsync, sbi->node_write should be acquired
through __write_node_folio to ensure that the IS_CHECKPOINTED flag
correctly indicates that the checkpoint write has been completed. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: vport: fix self-deadlock on release of tunnel ports
vports are used concurrently and protected by RCU, so netdev_put()
must happen after the RCU grace period. So, either in an RCU call or
after the synchronize_net(). The rtnl_delete_link() must happen under
RTNL and so can't be executed in RCU context. Calling synchronize_net()
while holding RTNL is not a good idea for performance and system
stability under load in general, so calling netdev_put() in RCU call
is the right solution here.
However,
when the device is deleted, rtnl_unlock() will call netdev_run_todo()
and block until all the references are gone. In the current code this
means that we never reach the call_rcu() and the vport is never freed
and the reference is never released, causing a self-deadlock on device
removal.
Fix that by moving the rcu_call() before the rtnl_unlock(), so the
scheduled RCU callback will be executed when synchronize_net() is
called from the rtnl_unlock()->netdev_run_todo() while the RTNL itself
is already released. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: microchip-core-qspi: don't attempt to transmit during emulated read-only dual/quad operations
The core will deal with reads by creating clock cycles itself, there's
no need to generate clock cycles by transmitting garbage data at the
driver level. Further, transmitting garbage data just bricks the transfer
since QSPI doesn't have a dedicated master-out line like MOSI in regular
SPI. I'm not entirely sure if the transfer is bricked because of the
garbage data being transmitted on the bus or because the core loses
track of whether it is supposed to be sending or receiving data. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix scheduling with atomic in timestamp sockopt
Using lock_sock_fast() (atomic context) around sock_set_timestamp()
and sock_set_timestamping() is unsafe, as both helpers can sleep.
Replace lock_sock_fast() with sleepable lock_sock()/release_sock()
to avoid scheduling while atomic panic. |
| Previously, a revoked 'SignatureKey' belonging to a CA was not correctly checked for revocation. Now, both the 'key' and 'key.SignatureKey' are checked for @revoked. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix missing last_unlink_trans update when removing a directory
When removing a directory we are not updating its last_unlink_trans field,
which can result in incorrect fsync behaviour in case some one fsyncs the
directory after it was removed because it's holding a file descriptor on
it.
Example scenario:
mkdir /mnt/dir1
mkdir /mnt/dir1/dir2
mkdir /mnt/dir3
sync -f /mnt
# Do some change to the directory and fsync it.
chmod 700 /mnt/dir1
xfs_io -c fsync /mnt/dir1
# Move dir2 out of dir1 so that dir1 becomes empty.
mv /mnt/dir1/dir2 /mnt/dir3/
open fd on /mnt/dir1
call rmdir(2) on path "/mnt/dir1"
fsync fd
<trigger power failure>
When attempting to mount the filesystem, the log replay will fail with
an -EIO error and dmesg/syslog has the following:
[445771.626482] BTRFS info (device dm-0): first mount of filesystem 0368bbea-6c5e-44b5-b409-09abe496e650
[445771.626486] BTRFS info (device dm-0): using crc32c checksum algorithm
[445771.627912] BTRFS info (device dm-0): start tree-log replay
[445771.628335] page: refcount:2 mapcount:0 mapping:0000000061443ddc index:0x1d00 pfn:0x7072a5
[445771.629453] memcg:ffff89f400351b00
[445771.629892] aops:btree_aops [btrfs] ino:1
[445771.630737] flags: 0x17fffc00000402a(uptodate|lru|private|writeback|node=0|zone=2|lastcpupid=0x1ffff)
[445771.632359] raw: 017fffc00000402a fffff47284d950c8 fffff472907b7c08 ffff89f458e412b8
[445771.633713] raw: 0000000000001d00 ffff89f6c51d1a90 00000002ffffffff ffff89f400351b00
[445771.635029] page dumped because: eb page dump
[445771.635825] BTRFS critical (device dm-0): corrupt leaf: root=5 block=30408704 slot=10 ino=258, invalid nlink: has 2 expect no more than 1 for dir
[445771.638088] BTRFS info (device dm-0): leaf 30408704 gen 10 total ptrs 17 free space 14878 owner 5
[445771.638091] BTRFS info (device dm-0): refs 4 lock_owner 0 current 3581087
[445771.638094] item 0 key (256 INODE_ITEM 0) itemoff 16123 itemsize 160
[445771.638097] inode generation 3 transid 9 size 16 nbytes 16384
[445771.638098] block group 0 mode 40755 links 1 uid 0 gid 0
[445771.638100] rdev 0 sequence 2 flags 0x0
[445771.638102] atime 1775744884.0
[445771.660056] ctime 1775744885.645502983
[445771.660058] mtime 1775744885.645502983
[445771.660060] otime 1775744884.0
[445771.660062] item 1 key (256 INODE_REF 256) itemoff 16111 itemsize 12
[445771.660064] index 0 name_len 2
[445771.660066] item 2 key (256 DIR_ITEM 1843588421) itemoff 16077 itemsize 34
[445771.660068] location key (259 1 0) type 2
[445771.660070] transid 9 data_len 0 name_len 4
[445771.660075] item 3 key (256 DIR_ITEM 2363071922) itemoff 16043 itemsize 34
[445771.660076] location key (257 1 0) type 2
[445771.660077] transid 9 data_len 0 name_len 4
[445771.660078] item 4 key (256 DIR_INDEX 2) itemoff 16009 itemsize 34
[445771.660079] location key (257 1 0) type 2
[445771.660080] transid 9 data_len 0 name_len 4
[445771.660081] item 5 key (256 DIR_INDEX 3) itemoff 15975 itemsize 34
[445771.660082] location key (259 1 0) type 2
[445771.660083] transid 9 data_len 0 name_len 4
[445771.660084] item 6 key (257 INODE_ITEM 0) itemoff 15815 itemsize 160
[445771.660086] inode generation 9 transid 9 size 8 nbytes 0
[445771.660087] block group 0 mode 40777 links 1 uid 0 gid 0
[445771.660088] rdev 0 sequence 2 flags 0x0
[445771.660089] atime 1775744885.641174097
[445771.660090] ctime 1775744885.645502983
[445771.660091] mtime 1775744885.645502983
[445771.660105] otime 1775744885.641174097
[445771.660106] item 7 key (257 INODE_REF 256) itemoff 15801 itemsize 14
[445771.660107] index 2 name_len 4
[445771.660108] item 8 key (257 DIR_ITEM 2676584006) itemoff 15767 itemsize 34
[445771.660109] location key (2
---truncated--- |
| Improper initialization in the UEFI firmware for some Intel platforms within Ring 0: Bare Metal OS may allow an information disclosure. System software adversary with a privileged user combined with a high complexity attack may enable data exposure. This result may potentially occur via local access when attack requirements are present without special internal knowledge and requires no user interaction. The potential vulnerability may impact the confidentiality (high), integrity (none) and availability (none) of the vulnerable system, resulting in subsequent system confidentiality (none), integrity (none) and availability (none) impacts. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: initialise extack before use
Fix missing initialisation of extack in flow offload. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix overwriting ct original tuple for ICMPv6
OVS_PACKET_CMD_EXECUTE has 3 main attributes:
- OVS_PACKET_ATTR_KEY - Packet metadata in a netlink format.
- OVS_PACKET_ATTR_PACKET - Binary packet content.
- OVS_PACKET_ATTR_ACTIONS - Actions to execute on the packet.
OVS_PACKET_ATTR_KEY is parsed first to populate sw_flow_key structure
with the metadata like conntrack state, input port, recirculation id,
etc. Then the packet itself gets parsed to populate the rest of the
keys from the packet headers.
Whenever the packet parsing code starts parsing the ICMPv6 header, it
first zeroes out fields in the key corresponding to Neighbor Discovery
information even if it is not an ND packet.
It is an 'ipv6.nd' field. However, the 'ipv6' is a union that shares
the space between 'nd' and 'ct_orig' that holds the original tuple
conntrack metadata parsed from the OVS_PACKET_ATTR_KEY.
ND packets should not normally have conntrack state, so it's fine to
share the space, but normal ICMPv6 Echo packets or maybe other types of
ICMPv6 can have the state attached and it should not be overwritten.
The issue results in all but the last 4 bytes of the destination
address being wiped from the original conntrack tuple leading to
incorrect packet matching and potentially executing wrong actions
in case this packet recirculates within the datapath or goes back
to userspace.
ND fields should not be accessed in non-ND packets, so not clearing
them should be fine. Executing memset() only for actual ND packets to
avoid the issue.
Initializing the whole thing before parsing is needed because ND packet
may not contain all the options.
The issue only affects the OVS_PACKET_CMD_EXECUTE path and doesn't
affect packets entering OVS datapath from network interfaces, because
in this case CT metadata is populated from skb after the packet is
already parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Set hugetlb mmap base address aligned with pmd size
With ltp test case "testcases/bin/hugefork02", there is a dmesg error
report message such as:
kernel BUG at mm/hugetlb.c:5550!
Oops - BUG[#1]:
CPU: 0 UID: 0 PID: 1517 Comm: hugefork02 Not tainted 6.14.0-rc2+ #241
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
pc 90000000004eaf1c ra 9000000000485538 tp 900000010edbc000 sp 900000010edbf940
a0 900000010edbfb00 a1 9000000108d20280 a2 00007fffe9474000 a3 00007ffff3474000
a4 0000000000000000 a5 0000000000000003 a6 00000000003cadd3 a7 0000000000000000
t0 0000000001ffffff t1 0000000001474000 t2 900000010ecd7900 t3 00007fffe9474000
t4 00007fffe9474000 t5 0000000000000040 t6 900000010edbfb00 t7 0000000000000001
t8 0000000000000005 u0 90000000004849d0 s9 900000010edbfa00 s0 9000000108d20280
s1 00007fffe9474000 s2 0000000002000000 s3 9000000108d20280 s4 9000000002b38b10
s5 900000010edbfb00 s6 00007ffff3474000 s7 0000000000000406 s8 900000010edbfa08
ra: 9000000000485538 unmap_vmas+0x130/0x218
ERA: 90000000004eaf1c __unmap_hugepage_range+0x6f4/0x7d0
PRMD: 00000004 (PPLV0 +PIE -PWE)
EUEN: 00000007 (+FPE +SXE +ASXE -BTE)
ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
ESTAT: 000c0000 [BRK] (IS= ECode=12 EsubCode=0)
PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
Process hugefork02 (pid: 1517, threadinfo=00000000a670eaf4, task=000000007a95fc64)
Call Trace:
[<90000000004eaf1c>] __unmap_hugepage_range+0x6f4/0x7d0
[<9000000000485534>] unmap_vmas+0x12c/0x218
[<9000000000494068>] exit_mmap+0xe0/0x308
[<900000000025fdc4>] mmput+0x74/0x180
[<900000000026a284>] do_exit+0x294/0x898
[<900000000026aa30>] do_group_exit+0x30/0x98
[<900000000027bed4>] get_signal+0x83c/0x868
[<90000000002457b4>] arch_do_signal_or_restart+0x54/0xfa0
[<90000000015795e8>] irqentry_exit_to_user_mode+0xb8/0x138
[<90000000002572d0>] tlb_do_page_fault_1+0x114/0x1b4
The problem is that base address allocated from hugetlbfs is not aligned
with pmd size. Here add a checking for hugetlbfs and align base address
with pmd size. After this patch the test case "testcases/bin/hugefork02"
passes to run.
This is similar to the commit 7f24cbc9c4d42db8a3c8484d1 ("mm/mmap: teach
generic_get_unmapped_area{_topdown} to handle hugetlb mappings"). |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l: async: Properly re-initialise notifier entry in unregister
The notifier_entry of a notifier is not re-initialised after unregistering
the notifier. This leads to dangling pointers being left there so use
list_del_init() to return the notifier_entry an empty list. |
| In the Linux kernel, the following vulnerability has been resolved:
efi: libstub: only free priv.runtime_map when allocated
priv.runtime_map is only allocated when efi_novamap is not set.
Otherwise, it is an uninitialized value. In the error path, it is freed
unconditionally. Avoid passing an uninitialized value to free_pool.
Free priv.runtime_map only when it was allocated.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: tcm_loop: Drain commands in target_reset handler
tcm_loop_target_reset() violates the SCSI EH contract: it returns SUCCESS
without draining any in-flight commands. The SCSI EH documentation
(scsi_eh.rst) requires that when a reset handler returns SUCCESS the driver
has made lower layers "forget about timed out scmds" and is ready for new
commands. Every other SCSI LLD (virtio_scsi, mpt3sas, ipr, scsi_debug,
mpi3mr) enforces this by draining or completing outstanding commands before
returning SUCCESS.
Because tcm_loop_target_reset() doesn't drain, the SCSI EH reuses in-flight
scsi_cmnd structures for recovery commands (e.g. TUR) while the target core
still has async completion work queued for the old se_cmd. The memset in
queuecommand zeroes se_lun and lun_ref_active, causing
transport_lun_remove_cmd() to skip its percpu_ref_put(). The leaked LUN
reference prevents transport_clear_lun_ref() from completing, hanging
configfs LUN unlink forever in D-state:
INFO: task rm:264 blocked for more than 122 seconds.
rm D 0 264 258 0x00004000
Call Trace:
__schedule+0x3d0/0x8e0
schedule+0x36/0xf0
transport_clear_lun_ref+0x78/0x90 [target_core_mod]
core_tpg_remove_lun+0x28/0xb0 [target_core_mod]
target_fabric_port_unlink+0x50/0x60 [target_core_mod]
configfs_unlink+0x156/0x1f0 [configfs]
vfs_unlink+0x109/0x290
do_unlinkat+0x1d5/0x2d0
Fix this by making tcm_loop_target_reset() actually drain commands:
1. Issue TMR_LUN_RESET via tcm_loop_issue_tmr() to drain all commands that
the target core knows about (those not yet CMD_T_COMPLETE).
2. Use blk_mq_tagset_busy_iter() to iterate all started requests and
flush_work() on each se_cmd — this drains any deferred completion work
for commands that already had CMD_T_COMPLETE set before the TMR (which
the TMR skips via __target_check_io_state()). This is the same pattern
used by mpi3mr, scsi_debug, and libsas to drain outstanding commands
during reset. |
| KDC in MIT Kerberos 5 (krb5kdc) does not set a global variable for some krb4 message types, which allows remote attackers to cause a denial of service (crash) and possibly execute arbitrary code via crafted messages that trigger a NULL pointer dereference or double-free. |
| The kernel in Apple Mac OS X 10.4 through 10.4.10 does not reset the current Mach Thread Port or Thread Exception Port when executing a setuid program, which allows local users to execute arbitrary code by creating the port before launching the setuid program, then writing to the address space of the setuid process. |
| The Hash-based Message Authentication Code (HMAC) provider in Java on Apple Mac OS X 10.4.11, 10.5.4, and 10.5.5 uses an uninitialized variable, which allows remote attackers to execute arbitrary code via a crafted applet, related to an "error checking issue." |
| Mozilla Firefox before 21.0, Firefox ESR 17.x before 17.0.6, Thunderbird before 17.0.6, and Thunderbird ESR 17.x before 17.0.6 do not properly initialize data structures for the nsDOMSVGZoomEvent::mPreviousScale and nsDOMSVGZoomEvent::mNewScale functions, which allows remote attackers to obtain sensitive information from process memory via a crafted web site. |
| Uninitialized memory in the JavaScript Engine component. This vulnerability was fixed in Firefox 142, Firefox ESR 128.14, Firefox ESR 140.2, Thunderbird 142, Thunderbird 128.14, and Thunderbird 140.2. |
| iccDEV provides a set of libraries and tools for working with ICC color management profiles. Prior to version 2.3.1.6, there is a defect in LUT dump/iteration logic affecting CIccCLUT::Iterate() and output produced by CIccMBB::Describe() (via CLUT dumping). This issue has been patched in version 2.3.1.6. |
| In the context switch logic Xen attempts to skip an IBPB in the case of
a vCPU returning to a CPU on which it was the previous vCPU to run.
While safe for Xen's isolation between vCPUs, this prevents the guest
kernel correctly isolating between tasks. Consider:
1) vCPU runs on CPU A, running task 1.
2) vCPU moves to CPU B, idle gets scheduled on A. Xen skips IBPB.
3) On CPU B, guest kernel switches from task 1 to 2, issuing IBPB.
4) vCPU moves back to CPU A. Xen skips IBPB again.
Now, task 2 is running on CPU A with task 1's training still in the BTB. |
