| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
exit: prevent preemption of oopsing TASK_DEAD task
When an already-exiting task oopses, make_task_dead() currently calls
do_task_dead() with preemption enabled. That is forbidden:
do_task_dead() calls __schedule(), which has a comment saying "WARNING:
must be called with preemption disabled!".
If an oopsing task is preempted in do_task_dead(), between becoming
TASK_DEAD and entering the scheduler explicitly, bad things happen:
finish_task_switch() assumes that once the scheduler has switched away
from a TASK_DEAD task, the task can never run again and its stack is no
longer needed; but that assumption apparently doesn't hold if the dead
task was preempted (the SM_PREEMPT case).
This means that the scheduler ends up repeatedly dropping references on
the dead task's stack, which can lead to use-after-free or double-free
of the entire task stack; in other words, two tasks can end up running
on the same stack, resulting in various kinds of memory corruption.
(This does not just affect "recursively oopsing" tasks; it is enough to
oops once during task exit, for example in a file_operations::release
handler) |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix double free in create_space_info_sub_group() error path
When kobject_init_and_add() fails, the call chain is:
create_space_info_sub_group()
-> btrfs_sysfs_add_space_info_type()
-> kobject_init_and_add()
-> failure
-> kobject_put(&sub_group->kobj)
-> space_info_release()
-> kfree(sub_group)
Then control returns to create_space_info_sub_group(), where:
btrfs_sysfs_add_space_info_type() returns error
-> kfree(sub_group)
Thus, sub_group is freed twice.
Keep parent->sub_group[index] = NULL for the failure path, but after
btrfs_sysfs_add_space_info_type() has called kobject_put(), let the
kobject release callback handle the cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fix race between ICReq handling and queue teardown
nvmet_tcp_handle_icreq() updates queue->state after sending an
Initialization Connection Response (ICResp), but it does so without
serializing against target-side queue teardown.
If an NVMe/TCP host sends an Initialization Connection Request
(ICReq) and immediately closes the connection, target-side teardown
may start in softirq context before io_work drains the already
buffered ICReq. In that case, nvmet_tcp_schedule_release_queue()
sets queue->state to NVMET_TCP_Q_DISCONNECTING and drops the queue
reference under state_lock.
If io_work later processes that ICReq, nvmet_tcp_handle_icreq() can
still overwrite the state back to NVMET_TCP_Q_LIVE. That defeats the
DISCONNECTING-state guard in nvmet_tcp_schedule_release_queue() and
allows a later socket state change to re-enter teardown and issue a
second kref_put() on an already released queue.
The ICResp send failure path has the same problem. If teardown has
already moved the queue to DISCONNECTING, a send error can still
overwrite the state with NVMET_TCP_Q_FAILED, again reopening the
window for a second teardown path to drop the queue reference.
Fix this by serializing both post-send state transitions with
state_lock and bailing out if teardown has already started.
Use -ESHUTDOWN as an internal sentinel for that bail-out path rather
than propagating it as a transport error like -ECONNRESET. Keep
nvmet_tcp_socket_error() setting rcv_state to NVMET_TCP_RECV_ERR before
honoring that sentinel so receive-side parsing stays quiesced until the
existing release path completes. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/iwcm: Fix workqueue list corruption by removing work_list
The commit e1168f0 ("RDMA/iwcm: Simplify cm_event_handler()")
changed the work submission logic to unconditionally call
queue_work() with the expectation that queue_work() would
have no effect if work was already pending. The problem is
that a free list of struct iwcm_work is used (for which
struct work_struct is embedded), so each call to queue_work()
is basically unique and therefore does indeed queue the work.
This causes a problem in the work handler which walks the work_list
until it's empty to process entries. This means that a single
run of the work handler could process item N+1 and release it
back to the free list while the actual workqueue entry is still
queued. It could then get reused (INIT_WORK...) and lead to
list corruption in the workqueue logic.
Fix this by just removing the work_list. The workqueue already
does this for us.
This fixes the following error that was observed when stress
testing with ucmatose on an Intel E830 in iWARP mode:
[ 151.465780] list_del corruption. next->prev should be ffff9f0915c69c08, but was ffff9f0a1116be08. (next=ffff9f0a15b11c08)
[ 151.466639] ------------[ cut here ]------------
[ 151.466986] kernel BUG at lib/list_debug.c:67!
[ 151.467349] Oops: invalid opcode: 0000 [#1] SMP NOPTI
[ 151.467753] CPU: 14 UID: 0 PID: 2306 Comm: kworker/u64:18 Not tainted 6.19.0-rc4+ #1 PREEMPT(voluntary)
[ 151.468466] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 151.469192] Workqueue: 0x0 (iw_cm_wq)
[ 151.469478] RIP: 0010:__list_del_entry_valid_or_report+0xf0/0x100
[ 151.469942] Code: c7 58 5f 4c b2 e8 10 50 aa ff 0f 0b 48 89 ef e8 36 57 cb ff 48 8b 55 08 48 89 e9 48 89 de 48 c7 c7 a8 5f 4c b2 e8 f0 4f aa ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90 90 90 90 90 90
[ 151.471323] RSP: 0000:ffffb15644e7bd68 EFLAGS: 00010046
[ 151.471712] RAX: 000000000000006d RBX: ffff9f0915c69c08 RCX: 0000000000000027
[ 151.472243] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f0a37d9c600
[ 151.472768] RBP: ffff9f0a15b11c08 R08: 0000000000000000 R09: c0000000ffff7fff
[ 151.473294] R10: 0000000000000001 R11: ffffb15644e7bba8 R12: ffff9f092339ee68
[ 151.473817] R13: ffff9f0900059c28 R14: ffff9f092339ee78 R15: 0000000000000000
[ 151.474344] FS: 0000000000000000(0000) GS:ffff9f0a847b5000(0000) knlGS:0000000000000000
[ 151.474934] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 151.475362] CR2: 0000559e233a9088 CR3: 000000020296b004 CR4: 0000000000770ef0
[ 151.475895] PKRU: 55555554
[ 151.476118] Call Trace:
[ 151.476331] <TASK>
[ 151.476497] move_linked_works+0x49/0xa0
[ 151.476792] __pwq_activate_work.isra.46+0x2f/0xa0
[ 151.477151] pwq_dec_nr_in_flight+0x1e0/0x2f0
[ 151.477479] process_scheduled_works+0x1c8/0x410
[ 151.477823] worker_thread+0x125/0x260
[ 151.478108] ? __pfx_worker_thread+0x10/0x10
[ 151.478430] kthread+0xfe/0x240
[ 151.478671] ? __pfx_kthread+0x10/0x10
[ 151.478955] ? __pfx_kthread+0x10/0x10
[ 151.479240] ret_from_fork+0x208/0x270
[ 151.479523] ? __pfx_kthread+0x10/0x10
[ 151.479806] ret_from_fork_asm+0x1a/0x30
[ 151.480103] </TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: reset op_nents when zerocopy page pin fails
When iov_iter_get_pages2() fails in rds_message_zcopy_from_user(),
the pinned pages are released with put_page(), and
rm->data.op_mmp_znotifier is cleared. But we fail to properly
clear rm->data.op_nents.
Later when rds_message_purge() is called from rds_sendmsg() the
cleanup loop iterates over the incorrectly non zero number of
op_nents and frees them again.
Fix this by properly resetting op_nents when it should be in
rds_message_zcopy_from_user(). |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix double free in ice_sf_eth_activate() error path
When auxiliary_device_add() fails, ice_sf_eth_activate() jumps to
aux_dev_uninit and calls auxiliary_device_uninit(&sf_dev->adev).
The device release callback ice_sf_dev_release() frees sf_dev, but
the current error path falls through to sf_dev_free and calls
kfree(sf_dev) again, causing a double free.
Keep kfree(sf_dev) for the auxiliary_device_init() failure path, but
avoid falling through to sf_dev_free after auxiliary_device_uninit(). |
| In numbers.c in libxslt 1.1.33, an xsl:number with certain format strings could lead to a uninitialized read in xsltNumberFormatInsertNumbers. This could allow an attacker to discern whether a byte on the stack contains the characters A, a, I, i, or 0, or any other character. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/vmw_pvrdma: Fix double free on pvrdma_alloc_ucontext() error path
Sashiko points out that pvrdma_uar_free() is already called within
pvrdma_dealloc_ucontext(), so calling it before triggers a double free. |
| In the Linux kernel, the following vulnerability has been resolved:
net: caif: clear client service pointer on teardown
`caif_connect()` can tear down an existing client after remote shutdown by
calling `caif_disconnect_client()` followed by `caif_free_client()`.
`caif_free_client()` releases the service layer referenced by
`adap_layer->dn`, but leaves that pointer stale.
When the socket is later destroyed, `caif_sock_destructor()` calls
`caif_free_client()` again and dereferences the freed service pointer.
Clear the client/service links before releasing the service object so
repeated teardown becomes harmless. |
| Concurrency and locking defects in GSS-TSIG |
| The egg-mkfont utility in Panda3D versions up to and including 1.10.16 contains an uncontrolled format string vulnerability. The -gp (glyph pattern) command-line option is used directly as the format string for sprintf() with only a single argument supplied. If an attacker provides additional format specifiers, egg-mkfont may read unintended stack values and write the formatted output into generated .egg and .png files, resulting in disclosure of stack-resident memory and pointer values. |
| A use of externally-controlled format string vulnerability in Fortinet FortiAnalyzer 7.6.0 through 7.6.4, FortiAnalyzer 7.4.0 through 7.4.7, FortiAnalyzer 7.2 all versions, FortiAnalyzer 7.0 all versions, FortiAnalyzer Cloud 7.6.2, FortiAnalyzer Cloud 7.4.1 through 7.4.7, FortiAnalyzer Cloud 7.2 all versions, FortiAnalyzer Cloud 7.0 all versions, FortiManager 7.6.0 through 7.6.4, FortiManager 7.4.0 through 7.4.7, FortiManager 7.2 all versions, FortiManager 7.0 all versions, FortiManager Cloud 7.6.2 through 7.6.3, FortiManager Cloud 7.4.1 through 7.4.7, FortiManager Cloud 7.2.1 through 7.2.10, FortiManager Cloud 7.0.1 through 7.0.14 may allow an attacker to escalate its privileges via specially crafted requests. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Remove redundant css_put() in scx_cgroup_init()
The iterator css_for_each_descendant_pre() walks the cgroup hierarchy
under cgroup_lock(). It does not increment the reference counts on
yielded css structs.
According to the cgroup documentation, css_put() should only be used
to release a reference obtained via css_get() or css_tryget_online().
Since the iterator does not use either of these to acquire a reference,
calling css_put() in the error path of scx_cgroup_init() causes a
refcount underflow.
Remove the unbalanced css_put() to prevent a potential Use-After-Free
(UAF) vulnerability. |
| A format string argument mismatch in Netatalk 3.0.3 through 4.4.2 allows a remote authenticated attacker to cause a minor denial of service via crafted input that triggers incorrect format string processing. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: rockchip-sfc: Fix double-free in remove() callback
The driver uses devm_spi_register_controller() for registration, which
automatically unregisters the controller via devm cleanup when the
device is removed. The manual call to spi_unregister_controller() in
the remove() callback can lead to a double-free.
And to make sure controller is unregistered before DMA buffer is
unmapped, switch to use spi_register_controller() in probe(). |
| In the Linux kernel, the following vulnerability has been resolved:
net-shapers: don't free reply skb after genlmsg_reply()
genlmsg_reply() hands the reply skb to netlink, and
netlink_unicast() consumes it on all return paths, whether the
skb is queued successfully or freed on an error path.
net_shaper_nl_get_doit() and net_shaper_nl_cap_get_doit()
currently jump to free_msg after genlmsg_reply() fails and call
nlmsg_free(msg), which can hit the same skb twice.
Return the genlmsg_reply() error directly and keep free_msg
only for pre-reply failures. |
| A flaw was found in nano. A local user could exploit a format string vulnerability in the `statusline()` function. By creating a directory with a name containing `printf` specifiers, the application attempts to display this name, leading to a segmentation fault (SEGV). This results in a Denial of Service (DoS) for the `nano` application. |
| Externally-controlled format string in PostgreSQL timeofday() function allows an attacker to retrieve portions of server memory, via crafted timezone zones. Versions before PostgreSQL 18.4, 17.10, 16.14, 15.18, and 14.23 are affected. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: meson-spicc: Fix double-put in remove path
meson_spicc_probe() registers the controller with
devm_spi_register_controller(), so teardown already drops the
controller reference via devm cleanup.
Calling spi_controller_put() again in meson_spicc_remove()
causes a double-put. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: hv: Fix double ida_free in hv_pci_probe error path
If hv_pci_probe() fails after storing the domain number in
hbus->bridge->domain_nr, there is a call to free this domain_nr via
pci_bus_release_emul_domain_nr(), however, during cleanup, the bridge
release callback pci_release_host_bridge_dev() also frees the domain_nr
causing ida_free to be called on same ID twice and triggering following
warning:
ida_free called for id=28971 which is not allocated.
WARNING: lib/idr.c:594 at ida_free+0xdf/0x160, CPU#0: kworker/0:2/198
Call Trace:
pci_bus_release_emul_domain_nr+0x17/0x20
pci_release_host_bridge_dev+0x4b/0x60
device_release+0x3b/0xa0
kobject_put+0x8e/0x220
devm_pci_alloc_host_bridge_release+0xe/0x20
devres_release_all+0x9a/0xd0
device_unbind_cleanup+0x12/0xa0
really_probe+0x1c5/0x3f0
vmbus_add_channel_work+0x135/0x1a0
Fix this by letting pci core handle the free domain_nr and remove
the explicit free called in pci-hyperv driver. |
